1 6

Quanzhou

6" Bush Hammer Tool with 6 inch Double Layer Plates for Angle Grinder (Arbor: 5/8"-11 Thread), 4 Rollers

6" Bush Hammer Tool with 6 inch Double Layer Plates for Angle Grinder (Arbor: 5/8"-11 Thread), 4 Rollers

$ 2,149.00 MXN
$ 3,000.00 MXN $ 2,149.00 MXN
Sale Sold out
Shipping calculated at checkout.
Size
View full details
Variant Variant total Quantity Price Variant total
Shaft: 5/8"-11 threaded
Shaft: 5/8"-11 threaded
$ 3,000.00
$ 2,149.00/ea
 $ 0.00
$ 3,000.00
$ 2,149.00/ea
 $ 0.00
Shaft: M14 threaded
Shaft: M14 threaded
$ 3,000.00
$ 2,214.00/ea
 $ 0.00
$ 3,000.00
$ 2,214.00/ea
 $ 0.00
View cart
0

Total items

$ 0.00

Product subtotal

Taxes, Discounts and shipping calculated at checkout
View cart

Item Features
Package Dimensions ‏ : ‎: 6.18 x 6.1 x 5.91 inches; 7.36 pounds


About this article:

  • Size: Double-layer plates, two plates of different sizes, one is 6 inches and the other is 5 inches.
  • Roller: 4 rollers, each roller with 30 tips.
  • Functions: 1. Creates a non-slip finish on granite and marble 2. Removes hard coatings and overlays 3. Surface preparation for coatings 4. Quickly exposes large aggregates 5. Increases concrete bond effectiveness
  • Adapt to adjustable speed angle grinder: Makita 9227CB/9237CB with adjustable speed is suggested. We do not recommend operating with too high speed, ideally less than 1000 RPM.
  • Removal of floor coverings and surface texturing.


ACTINTOOL 6 inch Double Layer Bush Hammering Plates Tool for Angle Grinder (Arbor: M14 Thread)






Product Description

6 inch bush hammer tool for angle grinder 

6 inch bush hammer

6 inch bush hammer tool 

6 inch/150mm Plate Bush Hammering Tool 

bush hammer tool for angle grinder

4*30 pin rollers 

4 rollers, each roller with 30 cone-shaped teeth. 

6 inch bush hammer for angle grinder.

general connector 

5/8-11" or M14 threaded shaft, general connector design. Fits low speed angle grinder and polisher. 

bush hammer for angle grinder

double layer plates 

Made with a 5 inch plate and a 6 inch plate. 

Bush hammer for texturing floors 

Lychee finish 

Lychee finish 

The lychee finish made with cone-shaped teeth is the coarsest finish we have. It is used to texturize surfaces or to remove heavy coatings. This finish is mainly seen outdoors because it has a non-slip effect. 

Star type finish 

Star roller finish. 

The finish made by the star roller is finer than the lychee finish. Each star blade has ten teeth made of tungsten material. 

Sandblasted finish 

Sandblasted finish 

Sandblasting is done using a knurled roller, each roller has 312 teeth. This finish is the best finish and is mostly seen indoors for stairs and bathroom floors. 

Application 

Bush hammer surface on stone

Creates non-slip finish on granite and marble. 

Repeatedly striking these carbide tips on stone or concrete surfaces creates a rough, pitted texture. 

Removing the coating with a bush hammer

Easy removal of hard coatings. 

Bush Hammer is applied for deep spraying of floors, especially when it is expected to remove thick surfaces such as thick coatings, very elastic coatings, asphalt, strong glue, thin-set ceramics, sanded grout, etc. 

bush hammer fast exposure large aggregate

Quickly expose large aggregates before polishing. 

To expose aggregate in concrete floors to prepare it for concrete polishing. 

Bush-hammering increases the effectiveness of the joint.

Surface preparation for new coatings. 

They can help increase bonding effectiveness when applying new concrete to an existing concrete surface by increasing the surface area of ​​the bond zone. 


Operation warning 

1. Working speed less than 1000 RPM. Not recommended for high RPM angle grinders, it is suggested to install bush hammer on adjustable speed angle grinder, such as makita 9227CB/9237CB polisher, speed lower than 1000RPM is suggested. 30-pin bush hammer roller is not recommended for 3-phase travel behind the grinder, too much pressure may break the bearings inside the roller. For 3-phase grinder, please use 45-pin bush hammer roller. 

2. Do not apply too much pressure on the bush hammer . This will prevent the roller from stopping and therefore decrease the life of the carbide tips.  

3. Adjust the plate distance for different finishes . For double-plate bush hammers, we can adjust the distance between two plates to have a finer or rougher finish. Widening the distance can have a rougher finish; on the contrary, the finish is finer if the distance is shortened. 

4. After each use, clean the rollers, dry them and apply oil to the spindles . It will be ideal to dip the rollers in oil to prevent the spindle from rusting. The tips of the rollers can be coated with diamond discs when they become inefficient.  

Features and details 

  • Size: Double-layer plates, two plates of different sizes, one is 6 inches and the other is 5 inches.
  • Roller: 4 rollers, each roller with 30 tips.
  • Functions: 1. Creates a non-slip finish on granite and marble 2. Removes hard coatings and overlays 3. Surface preparation for coatings 4. Quickly exposes large aggregates 5. Increases concrete bond effectiveness
  • Adapt to adjustable speed angle grinder: Makita 9227CB/9237CB with adjustable speed is suggested. We do not recommend operating with too high speed, ideally less than 1000 RPM.
  • Removal of floor coverings and surface texturing.